Outils pour utilisateurs
linux:pound (lu 33424 fois)
Différences
Ci-dessous, les différences entre deux révisions de la page.
|
linux:pound [03-12-2012 10:00] edmc73 |
linux:pound [04-04-2013 22:06] |
||
|---|---|---|---|
| Ligne 1: | Ligne 1: | ||
| - | ====== Pound : reverse proxy / load ballancer ====== | ||
| - | Installons maintenant **pound** qui permet le reverse-proxy et load-balancer | ||
| - | aptitude install pound | ||
| - | | ||
| - | Voici notre 1ère règle de config de pound | ||
| - | |||
| - | < | ||
| - | ListenHTTP | ||
| - | Address 70.70.70.70 | ||
| - | Port 80 | ||
| - | |||
| - | ## allow PUT and DELETE also (by default only GET, POST and HEAD)?: | ||
| - | xHTTP 0 | ||
| - | |||
| - | Service | ||
| - | HeadRequire "Host: .*www.p2pfr.com.*" | ||
| - | BackEnd | ||
| - | Address 192.168.0.2 | ||
| - | Port 80 | ||
| - | End | ||
| - | End | ||
| - | End | ||
| - | </ | ||
| - | |||
| - | <note tips> | ||
| - | HeadRequire supporte les expressions régulières, | ||
| - | "Host: .*(.p2pfr|p2pfr).com.*" | ||
| - | Pour tolérer 2 sites | ||
| - | " | ||
| - | </ | ||
| - | Lancez pound | ||
| - | / | ||
| - | | ||
| - | Mais comme le dis le message d' | ||
| - | < | ||
| - | pound will not start unconfigured. (warning). | ||
| - | Please configure; afterwards, set startup=1 in / | ||
| - | </ | ||
| - | |||
| - | Vous devez modifiez le fichier / | ||
| - | / | ||
| - | | ||
| - | ===== Configurer Apache : LogFormat poundCombined ===== | ||
| - | Comme le dit la page http:// | ||
| - | |||
| - | Si vous utilisez **awstats** ou un autre soft de statistique, | ||
| - | |||
| - | Pas de panique donc, le site cité ci dessus nous donne la solution. | ||
| - | |||
| - | Modifiez votre fichier de config de site apache, allez dans la section log et ajoutez cette ligne dans les types de log | ||
| - | | ||
| - | |||
| - | Ensuite modifier la variable suivante | ||
| - | CustomLog / | ||
| - | | ||
| - | | ||
| - | ===== Récupérer les log de pound ===== | ||
| - | source : http:// | ||
| - | |||
| - | |||
| - | Normally, sysklogd will overtake all messages from pound and will put them into syslog as anything with the facility ' | ||
| - | |||
| - | Just edit your / | ||
| - | |||
| - | #facility local0 is needed as sysklogd will | ||
| - | #seperate pound messages by this facility | ||
| - | LogFacility local0 | ||
| - | LogLevel 3 | ||
| - | |||
| - | And the change your / | ||
| - | |||
| - | ############### | ||
| - | #### RULES #### | ||
| - | ############### | ||
| - | | ||
| - | # | ||
| - | # First some standard log files. | ||
| - | # | ||
| - | *.*; | ||
| - | |||
| - | # get the messages with the facility local0 and | ||
| - | # log them into the pound logfile | ||
| - | local0.* -/ | ||
| - | |||
| - | The next step is to make sure that there is always a pound.log present. Therefore you need to modify the start script by adding a short conditional block into the top section of / | ||
| - | |||
| - | # Check if the pound.log exists, if not create one | ||
| - | if [ ! -e "/ | ||
| - | then | ||
| - | log_warning_msg "There is no pound.log, i'll create one" | ||
| - | touch / | ||
| - | chmod 0644 / | ||
| - | chown syslog:adm / | ||
| - | / | ||
| - | else | ||
| - | log_success_msg " | ||
| - | / | ||
| - | fi | ||
| - | |||
| - | After you reloaded the sysklogd by / | ||
| - | |||
| - | In my case the logfile increased to a size of more than 900 Mbyte after 24 hours, so don't forget to rotate the log. This could be done like this (/ | ||
| - | |||
| - | / | ||
| - | daily | ||
| - | missingok | ||
| - | rotate 14 | ||
| - | dateext | ||
| - | compress | ||
| - | notifempty | ||
| - | create 0644 syslog adm | ||
| - | postrotate | ||
| - | / | ||
| - | endscript | ||
| - | } | ||
| - | | ||
linux/pound.txt · Dernière modification: 04-04-2013 22:06 (modification externe)
Outils de la page
